Wiki

Aquarium plants turning yellow, brown or melting: what is wrong and what to do

Look at where the damage starts. Yellow old leaves and pinholes point to missing nutrients, pale new leaves to iron, and sudden melt after a change to plant stress that usually passes. If every plant slows down together, check light and CO₂ before adding fertiliser.

Updated · Scape Eden

Three questions that narrow it down

Plants rarely turn yellow or brown for one reason only, so do not reach for a bottle first. Answer three questions and you will usually land on one or two likely causes. Then fix one thing at a time and wait, because plants answer in weeks, not days.

  • Which leaves? Plants move some nutrients, such as nitrogen, phosphorus, potassium and magnesium, out of old leaves to feed new growth. So a shortage of those shows on the old, lower leaves first. Iron and calcium cannot be moved, so a shortage shows on the newest leaves first.
  • What does the damage look like? Yellow, pale with green veins, pinholes, see-through and soft, brown and stringy, or red turning green each point to a different cause. The list below matches each look to a guide.
  • What changed? A new tank, a new plant, a move or replant, a stronger light, new CO₂, a heatwave or a big trim all leave marks on plants within days or weeks. Write the change down with the date.

If every plant has slow growth and small leaves at once, the cause is probably not one missing nutrient. Stunted growth on all leaves usually points to too little light or CO₂, so read the balance section further down before you dose anything.

Match what you see to a guide

Missing nutrients

These are the most common causes in a tank with healthy water and settled plants. The pattern is the clue, and a few weeks is the fair time to judge whether a change worked.

  • Old leaves yellowing often means too little nitrogen. This is common in tanks with few fish or with frequent water changes, where the plants can use up the nitrogen supply. Test nitrate, and if it is low, feed with a complete fertiliser to its label. Remove badly yellowed leaves at the base.
  • Pinholes are the classic sign of too little potassium. An iron-only product is not a complete fertiliser, so check that yours lists potassium. Holed leaves never heal, so trim the worst and judge the fix by the new leaves.
  • Pale new leaves with green veins point to iron. Iron suppliers advise higher iron doses as pH and hardness rise, because iron is harder for plants to use in hard, alkaline water. See also pH swings if your water changes a lot.
  • Worn-out soil explains yellowing crypts and swords in a tank that was fine for months. Nutrient-rich aquasoil releases most of its food early, and two plant guides put its useful life at anywhere from a few months to about two years. Push root tabs in beside root-feeding plants and raise the liquid fertiliser to match.
  • Use the fertiliser calculator for amounts instead of guessing. Never pour in extra on top of the label. Melt right after planting is mostly a reaction to the change, so judge it by new growth rather than by adding more.

Melting after a move, a purchase or a change

Melt means leaves turn see-through, go soft and dissolve, often many at once. It is a stress reaction, not a disease. Buce Plant notes that farms usually grow plants with their leaves above the water, and leaves grown in air are not adapted to life underwater, so they slowly die off. Healthy roots and base can still grow new leaves.

  • Crypts melt when moved, replanted or hit by a change in water, light or temperature. Leave them in the soil, cut melted leaves at the base and keep conditions steady. New shoots usually appear within a few weeks, and Aquarium Co-Op suggests waiting at least three to four weeks before giving up. Our Wendt's crypt page has its care.
  • Tissue-culture plants come from sterile gel and often lose their first soft leaves. Trim melted or dying leaves and wait for new ones.
  • Bucephalandra leaves go dark or see-through after a change of place or water. Buce Plant says to judge it by the rhizome: green and firm is alive, black and brittle is dead and can be trimmed off. Its guide says new growth starts as tiny red shoots.
  • A rotting rhizome is different and needs action. Gensou says soft black rhizome rot is almost always caused by burying the rhizome or damaging it when planting. Lift the plant, cut away the soft tissue and attach it to wood or rock with the rhizome left uncovered. See Java fern and Anubias nana for how they sit.
  • Check that a new tank has finished cycling before you blame the plants. Read how to cycle a new tank, and see new tank syndrome and ammonia spikes.

Light, CO₂ and growth out of balance

Plants use light, CO₂ and nutrients together, and the scarcest one sets the pace. A shortage of any one of them holds back growth. Tropica calls CO₂ the main limit on growth in a planted tank, and notes that easy plants do not need added CO₂ but grow better with it, while Medium and Advanced plants do need it.

Heat, moss and red colour

  • Moss browns when the water runs warm, when a thick mat traps dirt and rots from inside, or when flow is weak. One guide says common mosses cope up to about 28 °C, and another puts the limit near 30 °C. Rinse the moss, cut off the brown underside and tie the healthy green part back on thinly. Check tank too hot and dead spots with no flow if your tank runs warm.
  • Red plants turning green is a looks problem. Buce Plant says red colour needs bright light, plenty of CO₂ and a good fertiliser, and that some cultivars stay green even under strong light. See too little light for the light side.
  • Warm water holds less dissolved gas, and Buce Plant says warmer plants need more CO₂ and nutrients, so a heatwave can shift the whole balance.

Fix it in order

  1. Rule out the water first. Test ammonia, nitrite and nitrate, and check the temperature. If readings are off, read high nitrate or how to cycle a new tank.
  2. Check the balance. Is the light too strong for your CO₂, or too weak for the depth?
  3. Change only one thing at a time, then wait two to three weeks. Judge by new leaves, not old ones, because damaged leaves do not recover.
  4. Remove dead and melted leaves at the base so they do not rot in the tank.
  5. Fill bare ground with fast plants, as too few plants at the start explains, and avoid too many species at once.
  6. Plan your plants and soil before you buy with the substrate calculator, and read aquascaping for beginners if you are starting again.

Our problem guides are drafts that an expert has not yet reviewed. Steady conditions for a few weeks will tell you more than another bottle.

Keep reading

Sources

We read these pages and wrote the guide in our own words. Species, problem and tool details come from our own wiki pages linked above.

How we made this

Written with AI assistance from the sources listed here and checked against them. Not yet reviewed by an expert. Report a mistake · How we write and check pages