Wiki

How long should you wait before adding fish to a new planted tank?

Wait until a liquid test kit reads zero ammonia and zero nitrite, and keeps doing so after a test dose of ammonia. Sources suggest roughly three to six weeks, but a planted tank can be quicker or far slower. Then add a few small, hardy fish, testing after each.

Updated · Scape Eden

The short answer: let the tests decide, not the calendar

There is no single number of days that makes a new tank safe. Guides give different waits: Dennerle says to wait about three weeks, until the nitrite reading has risen and then fallen back to zero. Tropica advises delaying fish for three to four weeks in a planted tank, until the plants have established. Practical Fishkeeping says a fishless cycle often takes four to six weeks, and an older, unsigned Usenet FAQ talks of two to six weeks. Aquarium Science gives the widest range, saying a planted start-up can take anywhere from two to twenty weeks.

That spread is the point. The wait depends on how fast the filter bacteria and the plants settle in, and that varies from tank to tank. Use the weeks above as a rough expectation and the readings below as the real decision. The chemistry behind the readings is covered in the cycling guide, so this page sticks to the decision itself.

What must be true before the first fish

  1. Ammonia and nitrite both read zero on a liquid test kit. Ammonia and nitrite are the two readings that harm fish, and ammonia and nitrite are the first things to test.
  2. The zero holds under load. In a fishless cycle that means dosing ammonia and finding both readings back at zero a day later. Practical Fishkeeping and Aquarium Science both use a 24-hour dose test, and Fishiverse repeats it on three days in a row, a cautious habit worth copying.
  3. The tap water is treated. Chlorine can be left to stand out, but chloramine does not leave water that way, according to both Aquarium Co-Op and UF/IFAS, so use a conditioner that handles both. See chlorine and chloramine.
  4. The temperature has settled at the setting you want and stays there. Check it with a thermometer for a few days before fish arrive; a heater that is correctly sized makes this easier.
  5. The filter has been running without a break. Bacteria live on the media and need moving, oxygenated water. If the filter was switched off for long, see power cuts.
  6. In a planted tank, the plants are alive and growing. Aquarium Science counts new leaves and new shoots as part of finishing a planted cycle, not only a clean ammonia test.

Nitrate is a grey area. The Usenet FAQ treats nitrate appearing as evidence of a working cycle, while Aquarium Science says it does not have to show. Either way, a high nitrate reading after weeks of dosing ammonia is worth bringing down with a water change before fish go in (see high nitrate).

Fishless or fish-in: which route to choose

Aquarium Science ranks the options in this order of preference: no plants and no fish, then plants only, then plants and fish together. Wikipedia's fishkeeping article lists three families of approach: fishless cycling, silent cycling with fast-growing plants, and slow stocking over six to eight weeks.

A fishless cycle is the safest choice for a planted tank you care about. No animal is exposed while the bacteria are still catching up, and you can run the finish test before anyone moves in.

A fish-in start means a few animals live in water that may turn toxic. The Usenet FAQ suggests one or two hardy, inexpensive fish as the ammonia source, and Practical Fishkeeping says to be ready with large water changes and a conditioner during the spikes. If you go this way, test daily, keep the stock very small and do not add more until both readings stay at zero. Do not cycle with shrimp in the tank; see shrimp-safe fish and plants.

Why a planted tank may be ready sooner, or much later

Plants take up ammonia directly. Aquarium Science notes that plants may absorb ammonia before the bacteria are established, and Wikipedia lists silent cycling with fast-growing plants as a recognised way to start a tank. With a lot of healthy growth from day one, readings can stay at zero without ever showing a spike.

The same sources and others show why this is unreliable, so treat it as a possible bonus, not a plan:

  • New plants often die back after planting while they switch to growing underwater, and Aquarium Science says this can delay their ammonia uptake for weeks or even months.
  • Aquarium Science reports that ammonia is often high when the lights come on in the morning and gone by the end of the lit period. That is one author's observation, but it is a good reason to test at a steady time each day and not read too much into one clean result.
  • Aquarium Science notes that soil balls around some plants can release ammonia for a long time, so a soil-based substrate may make the first weeks harder to predict.
  • Dennerle points out that plants live off their own reserves at first, which is why it starts fertiliser only in the second week, at half the usual dose.

So the rule does not change: a planted tank is ready when the tests and the plants both say so. Tropica puts it as keeping plant growth, fish numbers and filtration in balance, and calls the first 90 days critical. The step-by-step set-up guide and the no-CO₂ guide show how those first weeks fit together, and the beginner plant list suggests fast, forgiving species to start with.

A safe first stock: few, small and hardy

Sources agree on the direction: start small and build up. Aquarium Science says not to add a lot of fish or a large fish at first, and Practical Fishkeeping warns against adding the full stock in one go. They disagree on how big the first batch should be. One fishless-cycling guide is comfortable with most of the planned stock once the finish test is passed, while the fish-in advice is far more cautious. Choose the cautious end if you are unsure.

  • Pick the first fish from species that suit your water and tank size. The tank mates calculator shows which species get along, and the plant finder helps you fit the planting to the same water.
  • Check adult size and total numbers against the real volume, which the tank volume calculator works out. A tank stocked beyond what its filter and water changes can handle keeps producing problems (see overstocking).
  • Space the additions out. Dennerle suggests intervals of one to two weeks so the filter bacteria can adapt to the growing load, and Wikipedia describes building up the stock over six to eight weeks.
  • Consider leaving shrimp and other sensitive animals for last, once the tank has been steady with fish in it. The shrimp-safe guide covers which fish and plants are safe around them.
  • Feed lightly. Aquarium Science suggests feeding lightly when cycling with plants and fish, and leftover food turns into ammonia (see overfeeding).

Not every early death is a cycling problem. Fish can also be lost to transport stress or a disease brought home from the shop, which is covered in deaths after new fish.

Test after every addition

Each new fish adds waste, so each addition is a small test of the filter. Fishiverse suggests testing daily for the first week after adding fish, and a Hitchcock Center blog describes testing daily while a fish-in tank builds its filter. Test ammonia and nitrite each day after an addition, then wait until both stay at zero before adding the next group.

Keep up the weekly routine as well. Plants and water changes are how nitrate gets removed over time, according to Practical Fishkeeping, and the water change calculator helps you work out what a change does to your readings.

If ammonia or nitrite appears after fish go in

Any reading above zero means the filter is not keeping up. Ammonia becomes more toxic as pH rises, a point made by both the FAO and Aquarium Science, so a pH on the high side makes a given ammonia reading worse. Act the same day:

  1. Re-test to confirm the reading, then stop adding fish and cut back feeding for the moment.
  2. Do a partial water change with conditioned, temperature-matched water. Practical Fishkeeping and the Usenet FAQ both use water changes to dilute the problem; the problem guides for ammonia and nitrite give the amounts. Repeat until both readings are back at zero.
  3. A conditioner that binds ammonia can buy time. Follow its label, and remember it is a stop-gap and not a fix.
  4. Remove uneaten food and anything dead, then feed less when feeding resumes.
  5. Look for the cause. Aquarium Science argues that a persistent ammonia reading usually points to a filter problem, not something big water changes can fix alone, and names an over-cleaned filter (crash after filter cleaning) and too little biofiltration for the load as the usual causes. Too many fish (overstocking) or a stocking step that was too big fit the same pattern.

If fish are already struggling, the new tank syndrome guide covers the first hour. A filter that suits the tank and a sensible flow rate help prevent a repeat.

Quick checklist before the first fish

  • Ammonia and nitrite read zero on a liquid kit, and stay at zero after a test dose.
  • Water is conditioned for chlorine and chloramine, and the temperature is steady.
  • Plants are alive and showing new growth, and the filter has run non-stop.
  • The first fish are few, small and hardy, chosen for the tank size.
  • You have time to test daily for the next week and space the next batch out.
  • You know what to do if a reading goes above zero.

Rushing is a classic start-up error (see beginner aquascaping mistakes). If you are still gathering equipment, the shopping list and beginner aquascaping guide put the whole start-up in order.

Keep reading

Sources

We read these pages and wrote the guide in our own words. Species, problem and tool details come from our own wiki pages linked above.

How we made this

Written with AI assistance from the sources listed here and checked against them. Not yet reviewed by an expert. Report a mistake · How we write and check pages