Wiki

pH, GH and KH explained: what to test and what to do

pH is how acidic the water is, GH is calcium and magnesium, and KH is the carbonate buffer that holds pH steady. Test your tap water, pick livestock and plants that suit it, and avoid sudden changes rather than chasing a number with chemicals.

Updated · Scape Eden

The short version

Three numbers on a test kit confuse almost every new keeper, and they are not versions of the same thing. Learn which job each does and most of the confusion goes away.

  • pH: a scale from acidic to alkaline, with 7 as neutral.
  • GH (general hardness): dissolved calcium and magnesium, the minerals animals and plants take up.
  • KH (carbonate hardness): carbonate and bicarbonate, the buffer that keeps pH from lurching.

The practical rule: find out what your tap water already is, choose livestock and plants that suit it, and avoid sudden changes.

pH: acid or alkaline

pH is a scale where 7 is neutral, lower is acidic and higher is alkaline (Wikipedia: pH). It is logarithmic, so every whole unit is a tenfold step. Fishprofiles and Seneye both make the point: pH 5.5 is ten times more acidic than pH 6.5, so a shift from 7.0 to 6.0 is a big event for an animal in the water, even though it looks small on the kit.

For common community fish the sources differ: Aquarium Co-Op says most do well from 6.5 to 8.0, Fishprofiles says 6.5 to 7.5 will suit most species, and Aquarium Science says an average between 6.5 and 8.5 usually works. Treat 6.5 to 7.5 as the safe overlap and check each species. Aquarium Co-Op says South American fish and crystal shrimp tend to prefer lower pH, while African cichlids and livebearers prefer higher pH. The tank mate checker is a good way to find species that agree on water.

GH: the minerals

General hardness is the amount of dissolved calcium and magnesium. Aquarium Co-Op and Fishprofiles define it that way. Aquarium Co-Op and Global Seafood Alliance both say fish need calcium for bone development, and Aquarium Co-Op adds that shrimp moulting and snail shells depend on these minerals too. Most chlorophylls bind magnesium (Wikipedia: Chlorophyll), which is why plants need it as well.

If shrimp are struggling, read failed moult and sudden shrimp deaths alongside your GH reading.

KH: the buffer

Carbonate hardness measures carbonate and bicarbonate in the water (Wikipedia: Carbonate hardness). These ions soak up acid. A Mississippi State extension sheet calls them a buffer system against drastic pH changes: in low-alkalinity pond water pH can swing from 6 or lower to 10 or above, but in high-alkalinity water only between about 7.5 and 8.5.

Seneye says a daily rise and fall in pH is normal and that KH mostly sets its size: low KH means a big swing, high KH means pH is hard to move. This is why the pH crash and swings guide starts with KH, not pH.

A note on names: pond and lab sources call this alkalinity. Wikipedia says the gap is negligible below pH 8.5, so a KH reading works as your buffer measure.

How GH and KH relate

They often travel together because limestone and chalk release both calcium and carbonate. Aquarium Co-Op notes that limestone raises both GH and KH at once, and the Mississippi State sheet says most waters have similar values for the same reason. They are still different things: the same sheet says water can be high in alkalinity without being hard if the carbonate arrives as sodium or potassium salts, and Wikipedia describes hardness from sulfates and chlorides rather than bicarbonate. Test both rather than guessing one from the other.

Units and conversions

Hardness comes in several units, which is half the trouble. A degree of hardness (dGH or dKH) and a part per million of calcium carbonate are two ways of writing the same amount:

  • 1 dKH is about 17.9 ppm of calcium carbonate on the API test kit's own page and at Aquarium Co-Op, 17.8 ppm on Fishprofiles and 17.848 mg/L on Wikipedia. Use 17.9 for a quick sum and expect small rounding differences.
  • The same factor applies to GH: Wikipedia gives 1 German degree of hardness as about 17.85 ppm, and the API kit counts one drop as 1 dGH or 17.9 ppm.
  • ppm and mg/L are used interchangeably in these sources, so a supplier report in mg/L converts the same way.

Words like soft and hard are not standard either. Wikipedia puts soft water at 0 to 60 ppm, while Thames Water calls anything up to 100 mg/L soft. Trust the number, not the label.

Tap water and testing

Your tap water sets your starting point, and it varies from place to place. Water that runs through limestone, chalk or gypsum picks up calcium and magnesium, as Wikipedia explains. Thames Water says its supply is hard because of the chalky limestone the water passes through. Your water supplier can usually tell you its hardness; confirm it with your own test. Chlorine and chloramine in tap water are a separate matter, covered in chlorine and chloramine.

A liquid drop kit works by adding drops to a water sample until the colour changes; with the API kit the drop count is the reading in dGH or dKH. Strips are read by colour comparison. Test both the tap water and the tank, and write the numbers down. The equipment consumables page lists kits; if you are still cycling, start with the cycling guide.

Stability matters more than the number

Seneye says that if the fish are happy, a controlled and constant pH matters most, and Aquarium Co-Op says fish hit by rapid pH changes can show frantic swimming, lethargy or fast breathing. The sources differ on how fast is too fast: Fishprofiles says a change of more than 0.3 pH units a day is known to stress fish, while Seneye calls anything above 0.5 a day deadly or bad. Aquarium Science takes the opposite view and argues that fish cope with pH swings. The cautious reading is to keep changes small and slow.

So a steady routine beats a clever fix. Regular, modest water changes with the same tap water (see the water change calculator and the weekly routine) keep the tank close to your tap water. Our old tank syndrome guide covers what goes wrong when a neglected tank gets one big change.

What your livestock and plants care about

Start from the species, not from a target. Each fish and invertebrate page lists pH and hardness ranges; compare betta, neon tetra and bronze corydoras before putting them together.

Shrimp are where hardness matters most. Cherry shrimp (Neocaridina davidi) are the forgiving ones: Gensou and Shrimp Science both give pH 6.5 to 8.0 and describe them as tolerating relatively hard water, and Gensou says they cope with its local tap water with little more than dechloramination. Test your own tap first. Crystal and bee shrimp (Caridina cantonensis) are the opposite: Wikipedia says their health depends on soft water that matches the pH of their native streams, and Aquarium Co-Op says they prefer lower pH. Caridina is a big genus, so check each species, for example Amano shrimp. The shrimp-safe fish and plants guide covers companions.

Plants vary too. In our records 189 of 390 plants are rated as coping with hard water and 40 as soft water only; the rest are caution or unrated, and the records are drafts. Wendt's crypt is rated as coping, Mexican rotala as soft only. Use the plant finder to narrow the list.

CO2 dissolves to form a weak acid, so injecting it lowers pH. Tropica explains that the pH you should aim for depends on both the KH of your water and the CO2 level you want, with the example that at 12 dKH the target is pH 7.5 to 7.8. Aquarium Science shows the relationship is steep: at KH 3 its figures rise about 1.6 times with every 0.2 pH lost, which works out (our arithmetic) to roughly ten times the CO2 per whole pH unit. It also warns that other acids, such as phosphates and humic acids, lower pH too, so a pH-and-KH estimate can be wrong.

In a CO2 tank the buffer is what stops a daily pH dip becoming a crash, and our pH crash guide suggests keeping some KH rather than running near zero. The CO2 tool does the pH and KH sum for you, and too much CO2 covers the warning signs. If you are not injecting gas, see planted tank without CO2. The CO2 equipment section lists gear.

What not to do

  • Do not chase a number with a bottle. Fishprofiles says the larger the KH, the more resistant pH is to change, so a bottle has to fight the buffer; Aquarium Co-Op recommends mixing in RO water instead of using chemical adjusters. Some pH-lowering products use phosphoric acid, which adds phosphorus to the water (Fishprofiles; a hydroponics source, Science in Hydroponics, agrees), and Fishprofiles adds that this can stimulate algae. Formulas differ, so read the label.
  • Do not correct a low reading fast; our pH crash guide says a fast correction is another swing.
  • Do not change several things at once. Bulk Reef Supply stresses gradual change, and Fishprofiles' daily limit points the same way.
  • Do not blame pH for everything. Nitrate has its own page (high nitrate), and so does worn-out soil, which in our records lets pH and KH creep up.

Where RO water fits

Reverse osmosis removes dissolved ions, including calcium and magnesium (Wikipedia). Bulk Reef Supply says RO/DI water can read near 0 ppm TDS and has very few minerals, so it generally needs remineralising before it is the main water for a tank. Aquarium Co-Op mentions mixing it in gradually to lower hardness. Never add pure RO straight to a tank with animals in it; our pH crash guide lists that as a cause of crashes. Consider it only when your tap water is a poor match for your species.

A simple way to start

Test your tap water for pH, GH and KH and compare it with your chosen species pages. If they agree, change nothing and keep water changes regular. If not, pick different species or plan a gradual change. Starting a tank? Read the step-by-step setup guide next.

Keep reading

Sources

We read these pages and wrote the guide in our own words. Species, problem and tool details come from our own wiki pages linked above.

How we made this

Written with AI assistance from the sources listed here and checked against them. Not yet reviewed by an expert. Report a mistake · How we write and check pages