Wiki

Free aquarium calculator

Aquarium heater and chiller calculator

How many watts of heater your tank needs for your room, and whether a hot room needs a fan or a chiller to keep the water cool enough.

Your tank and room

L
Litres of actual water, not the tank's label size. Don't know it? Work it out with the tank volume calculator
°C
°C
The lowest the room reaches, day or night, in the coldest month.
°C
The highest the room reaches in the hottest month, including afternoons with the AC off during load-shedding.
Tank top

Extras

Results

Heater90 WFor a 10 °C gap
Room above target9 °C
CoolingNeeds a chiller
Heater
The room drops 10 °C below your target. That gap, times your water volume, sets the watts a heater needs to hold the line.
A chiller is the safer bet
The room runs 9 °C above your target — more than a clip-on fan's usual 2 °C of evaporative cooling. A compressor chiller (or a Peltier unit on a nano tank) will hold the line through the hottest afternoons.
A fan still helps
A fan alone won't close a 9 °C gap, but running one alongside the chiller cuts its workload and runtime.

The link and the PDF keep your numbers, so you can come back or share them.

Heaters that fit

Rated for your volume (where the maker states a tank range) and at least the watts above.

Clip-on fans

Chillers that fit

Compressor and Peltier units rated for your tank volume.

Use these numbers

Carry your tank's real water volume into the other calculators.

How this calculator works

Enter your tank's real water volume, the water temperature you're aiming for, and the coldest and hottest your room gets. The calculator works out the heater watts to hold the line on cold nights, and whether a hot afternoon needs only a fan or a proper chiller.

How heater sizing works

Watts needed scale with three things: how many litres you're heating, how far the coldest room reading sits below your target, and how much heat the tank loses through the glass. We use about 0.15 W per litre per °C of that gap — a figure that sits between the old temperate rule of thumb (3-5 W per litre for a large rise in a cold room) and the much smaller gap most hot-climate rooms actually see (roughly 0.5-1 W per litre in hot climates). An open top with no lid loses heat about 1.5× faster than a lidded tank of the same size, so it needs a heater that much stronger for the same gap.

Two heaters instead of one

Once a tank needs around 100 W or more, splitting that load across two smaller heaters is the safer choice. If one heater fails stuck on, a smaller unit pushes the temperature up more slowly and for less total wattage, giving you a better chance of noticing before it's a problem.

Cooling a hot room

When the room runs above your target, a clip-on fan blowing across the open water surface cools it by evaporation — typically 2-4 °C, depending on the model and how open the top is. If your room's peak is inside that range, a fan is usually enough and is far cheaper to run than a chiller. Beyond that, a compressor chiller (or a small Peltier unit on a nano tank) is the reliable fix; size it by the tank volume range the maker states, and expect its rated cooling capacity to fall off in a hot room compared to the maker's cooler test conditions.

Safety

  • Fit a heater guard on any bare-element heater in a tank with digging or grazing fish, and on any tank with children or pets nearby.
  • Never let a heater run dry: switch it off before you drop the water level for maintenance, and let it cool before refilling.
  • Run heaters through an independent thermostat or controller where the model doesn't have one built in, so a stuck dial can't cook the tank unnoticed.
  • Chillers and Peltier units need airflow around their vents; a closed cabinet traps their own exhaust heat and cuts their effective cooling.

Limits

These are planning figures, not a lab measurement of your room. Draughts, direct sun on the glass, an AC vent aimed at the tank, or a spot next to a stove all shift the real gap. During load-shedding, a heater or chiller does nothing without power — see the site's backup-power notes for that risk. For medication or dosing, always follow the product label.

Sources

Heater and chiller specs come from the makers' published data in the equipment wiki (heating and cooling). The sizing rules come from Scape Eden research notes that compare maker sizing charts with hobby rules for cold and hot climates.

Embed this calculator

Free to put on your own site, blog or forum. Paste the code where the calculator should appear.

Embed code

<iframe src="https://scapeeden.com/embed/tools/heater" title="Aquarium heater and chiller calculator by Scape Eden" width="100%" height="1200" style="border:0;max-width:100%" loading="lazy"></iframe><p><a href="https://scapeeden.com/tools/heater">Calculator by Scape Eden</a></p>

Optional: resize the frame to fit the calculator

<script>addEventListener("message",function(e){if(e.origin!=="https://scapeeden.com"||!e.data||e.data.type!=="scape-eden-embed-height")return;document.querySelectorAll('iframe[src^="https://scapeeden.com/embed/"]').forEach(function(f){if(f.contentWindow===e.source)f.style.height=e.data.height+"px"})})</script>

Without the resize script, give the frame at least 1200 pixels of height (taller in a narrow column).

Attribution rule: keep the “Calculator by Scape Eden” link under the frame, visible and unchanged, and do not hide the credit inside the frame. The calculators are planning estimates, not advice for a particular tank.

More calculators