Filter or pump stopped working or keeps cutting out
A filter or pump that has stopped no longer moves water through the media or stirs the surface. In a warm or crowded tank fish can be harmed quickly, so get air into the water first, then find out why it stopped.
Fish or shrimp can die within hours or days.
What you see
- No water coming out of the outlet and no sound from the motor
- A hum or buzz, but the impeller (the small spinning wheel in the pump) does not turn
- The filter runs for a while, then stops, or the power keeps tripping
- A flashing code on a filter or heater display
- The water surface is still and fish hang near the top
Could it be something else?
- Canister filter with weak flow or clogging: The filter still runs, but the flow is weak or slows down quickly
- Power cuts: outage plan: Everything in the house or on that circuit is off, not just the filter
- Heater failure, bubbles or safety worries: A flashing LF on a Fluval E-series heater is a heater message about water movement, not a dead filter
- Canister filter blowing bubbles or sucking air: Water is moving, but air is coming out with it
Why it happens
- No power reaching itA switched-off socket, a loose plug, or a tripped RCD or GFCI (a safety switch that cuts power when current leaks) will stop a filter. Fluval's manual says that if the RCD or GFCI switches off you should disconnect the power cord and remove the pump from the water, so treat it as a fault and do not keep resetting it.
- Dirty or jammed impeller and pump chamberGrime or debris can stop the impeller from spinning. Both Eheim and Fluval tell you to unplug the filter, take the pump apart and clean the impeller, the chamber and the shaft. Eheim warns that the impeller axle is ceramic and breaks easily.
- Worn or damaged pump partsFluval's manual lists the impeller and the motor seal ring as parts to check and clean every three months and replace yearly, and its warranty does not cover them as wear parts. A cracked or loose impeller or a damaged seal may stop the pump moving water even when the motor runs; the manuals do not describe this symptom, so treat that as our reasoning.
- Running dry or a closed water pathEheim and Fluval both say never to let the pump run dry. Fluval also says the intake strainer must be fully under water and the canister must hold enough water before the filter starts. A pump with closed valves or an unprimed canister has no water to move.
- A normal pause that looks like a faultFluval's FX4 and FX6 filters stop and restart on purpose. After you plug them in they run for 1 minute, rest for 2 minutes to clear air, then run on, and every 12 hours they pause for 1 minute to clear trapped air. A stop longer than these is not part of that cycle.
- A failed motor or damaged cordEheim and Fluval both say not to use a pump with a damaged cord or one that is not working properly, and that the cord cannot be replaced. Eheim says repairs must be done by its service centre. A motor that still will not run after a clean needs the maker's service centre or a replacement.
Fix it now
- Unplug the filter at the wall before you put your hands in the tank or touch the filter, and keep plugs and sockets dry
- Get air into the water now: point any other outlet at the surface, add an air stone and air pump, or stir the surface by hand, and feed little or nothing
- Check the socket and the RCD or GFCI. If the safety switch has tripped, take the pump out of the water and do not keep resetting it. Ask an electrician if it trips again
- Check that the tank water covers the intake, the valves are open, the hoses are not kinked and, on a canister, that it is filled and primed as your manual shows
- With the plug out, take the pump head apart as the manual shows and clean the impeller, the pump chamber and the shaft. Check the impeller turns freely and is not cracked, and that the seal ring sits properly
- Put it back together, restart it and watch it for several minutes. On a Fluval FX4 or FX6, allow for the planned 2-minute rest after you plug it in
- If it still will not run, or the cord or plug is damaged, stop using it and contact the maker's service centre or replace the filter. If it was off for hours, follow our power cuts guide before you restart it, and test ammonia and nitrite for the next few days
Stop it coming back
- Check and clean the impeller, shaft and seal on the maker's schedule, and replace worn impellers and seals
- Keep the water level high enough to cover the intake, and never run a pump dry
- Arrange a drip loop in every cord and plug the equipment into a socket protected by an RCD or GFCI
- Keep a battery air pump and air stone ready so the fish have oxygen if the filter fails
- Clean only part of the media at a time, and not on the same day as a pump repair, so the filter bacteria are not lost
Common questions
- Why has my filter pump stopped working?
- The usual causes are no power, a tripped safety switch, a dirty or cracked impeller, or the pump running dry. Unplug it, check these in order and clean the pump as the manual shows. If it still will not run, it may need the maker's service centre.
- My Fluval heater is flashing LF. Is the filter broken?
- No. Fluval's manual says LF means the E-series heater has detected poor water circulation around itself. The heater keeps operating, though not properly, and the message clears by itself once water flows past it again. Check the filter is running and that nothing blocks the heater.
- My internal filter hums but the water does not move. What now?
- Unplug it and clean the impeller, chamber and shaft, then check the impeller is whole and turns freely. Fluval lists the impeller as a wear part to replace yearly, so a cracked or worn one may need replacing. Eheim warns that the impeller axle is ceramic and breaks easily.
- Is it a problem if the filter is off for a few hours?
- It can be. With no flow the surface stops moving, so oxygen falls and the water in the filter can go stagnant. Add an air stone straight away, and see our power cuts guide for what to do before you restart it.
Still stuck?
Describe the problem and share a photo in the WhatsApp community group. Other keepers can often spot what is wrong.
Sources
How we made this
Written with AI assistance from the sources listed here and checked against them (September 2026). Not yet reviewed by an expert. Report a mistake · How we write and check pages
Cite this page
Copy a ready-made line to credit this page in your own writing.
Citation
Scape Eden. “Filter stopped working or cutting out: fixes”. Scape Eden aquarium wiki, updated October 15, 2026. https://scapeeden.com/wiki/problems/filter-stopped-working
Reference style (APA)
Scape Eden. (2026, October 15). Filter stopped working or cutting out: fixes. Scape Eden. https://scapeeden.com/wiki/problems/filter-stopped-working
Plain link
https://scapeeden.com/wiki/problems/filter-stopped-working
Text and data compiled by Scape Eden are free to reuse under CC BY 4.0 with attribution (credit Scape Eden and link to this page). Photos keep their own credited licences. Records are AI-assisted drafts with cited sources: see how we write and check this.
