Replacement parts for an old filter or heater
Old filters and heaters wear out in small parts: impellers, seals, hose connectors, foam and cartridges. A filter that has stopped cannot clean the water, and a faulty heater may not hold the temperature you set, so sort it out within days, and do not run kit that is cracked or missing a part.
Not an emergency, but it gets worse if left.
What you see
- The filter hums, rattles or grinds, or the water barely moves
- A seal, ring, plug, coupling or hose connector is cracked, hard or missing
- The impeller (the small spinning wheel in the pump) has chips or is broken
- Foam, cartridges or other media no longer fit, or are worn out
- The heater case is cracked, the cord is damaged, or the tank temperature does not match the setting
Could it be something else?
- Crash after cleaning the filter: The filter works, but ammonia or nitrite rose after a deep clean; no part is missing
- Power cuts: The equipment is fine, but the mains power is off
- Tank too hot: The heater is working but the room or lights are pushing the water temperature up
Why it happens
- Rubber parts drying out and hardeningOne maker says that a rubber hose connector can dry up and harden, so that air is pulled into the filter, and recommends replacing this inexpensive part once or twice a year.
- Pinched or distorted O-ringsThe same maker says a pinched or distorted O-ring can cause filter leaks, and advises silicone O-ring lubricant after servicing. It advises against Vaseline and other petroleum-based products.
- Debris jamming the impellerTetra says that debris such as fish waste and mineral deposits can clog the impeller assembly until the filter stops. A separated or damaged impeller needs a new one.
- Older modelsParts for older models can be hard to find. Look the part up by the model or type number on the label, and use parts listed for your model.
- A heater that has failed or is damagedOne heater maker says a heater with a damaged cord or plug, or one that is malfunctioning, must not be used, and that the cord cannot be replaced, so the heater should be discarded.
Fix it now
- Unplug the filter or heater from the mains before you touch it or put your hands in the tank
- For a heater, unplug it and let it cool before you lift it out of the water. One maker says at least 30 minutes, and another says to unplug first, let it cool, then remove it. Never run a heater out of the water
- Find the model or type number on the label of the filter or heater, and write it down before you search for parts
- Look up the part by that number on the maker's own website or spare-parts list first. If it is sold out, ask a dealer who stocks that maker before you buy a look-alike
- Replace damaged parts with the maker's own or an exact match: impeller, seals and hose connectors. Do not run a filter with a chipped or broken impeller
- Buy foam and cartridges listed for your model. When you refit media, one maker advises the finest foam in the bottom basket, and granular media in a media bag so particles cannot reach the pump
- If the old filter cannot be fixed and you replace it, read our guide on crashes after filter cleaning before you move or throw away the old media
- If a heater is cracked, has a damaged cord or plug, or is not holding the temperature, stop using it and replace it with one the maker rates for your tank size. Do not try to repair it yourself. One maker says a new heater can take 36 hours to settle, so judge it only after that
Stop it coming back
- Keep the manual, or a photo of the label with the model or type number, and check each part's condition whenever you clean the filter
- Keep a spare hose connector and seals for the model you use, if they are still sold
- Replace rubber parts that have gone hard before they fail, and do not wait for a leak
- Fit a drip loop in the power cords so that water cannot run down them to the socket, and use a socket with an RCD or GFCI (a safety cut-out) for aquarium equipment
Common questions
- Where can I find a replacement impeller for an old filter?
- Start with the maker's website and look the part up by the model or type number on the filter's label. If the maker no longer lists it, a dealer that stocks that maker may still have it. Use the exact part for your model.
- Can I use filter cartridges or foam that are not from the filter's maker?
- We found no reliable source on whether third-party media works as well. The safest choice is media listed for your model. If you use another type, check that it fits so water cannot bypass it, and keep testing for ammonia and nitrite.
- A seal or O-ring on my canister filter is missing or cracked. What now?
- Do not run the filter with a damaged seal, as a bad O-ring can cause leaks. Look up the seal by your filter's type number and replace it with the maker's part. Use silicone O-ring lubricant, not petroleum jelly.
- Is it safe to keep using an old heater?
- Only if the case, cord and plug are undamaged and it holds the temperature you set. Check the water with a thermometer, and give a new heater time to settle first. If the glass is cracked or the cord is damaged, unplug it and replace it.
Still stuck?
Describe the problem and share a photo in the WhatsApp community group. Other keepers can often spot what is wrong.
Sources
How we made this
Written with AI assistance from the sources listed here and checked against them (September 2026). Not yet reviewed by an expert. Report a mistake · How we write and check pages
Cite this page
Copy a ready-made line to credit this page in your own writing.
Citation
Scape Eden. “Replacement parts for an old filter or heater”. Scape Eden aquarium wiki, updated October 15, 2026. https://scapeeden.com/wiki/problems/replacement-parts-old-filter-heater
Reference style (APA)
Scape Eden. (2026, October 15). Replacement parts for an old filter or heater. Scape Eden. https://scapeeden.com/wiki/problems/replacement-parts-old-filter-heater
Plain link
https://scapeeden.com/wiki/problems/replacement-parts-old-filter-heater
Text and data compiled by Scape Eden are free to reuse under CC BY 4.0 with attribution (credit Scape Eden and link to this page). Photos keep their own credited licences. Records are AI-assisted drafts with cited sources: see how we write and check this.
