CO₂ solenoid clicking, lagging or not working
A CO₂ solenoid is an electric on/off valve for the gas, usually run by a timer or pH controller. If it clicks again and again, opens late, hums, or will not open or close, CO₂ may not reach the plants or may keep flowing when it should not.
Not an emergency, but it gets worse if left.
What you see
- The solenoid clicks on and off repeatedly
- It hums or buzzes loudly
- Gas takes a while to appear after the solenoid switches on
- No gas flows even when its light is on
- Bubbles keep going after the solenoid is switched off
Could it be something else?
- Regulator pressure problems: The gauges read zero, too high or keep rising
- Bubble rate drifting or in bursts: The solenoid switches fine but the count moves
- Too much CO₂: The fish are in trouble; turn the gas off first
- pH swings: A pH controller that is switching the solenoid on and off can look like a faulty solenoid
Why it happens
- Timer or power supply faultNo power, the wrong supply or a bad connection stops the coil working. Loud buzzing can mean the wrong voltage or supply.
- Working pressure too low for the valveSome valves need a minimum line pressure to open. Check your valve's specification.
- Dirt on the plunger or in the orificeDebris from the cylinder can stop the plunger sealing, so bubbles carry on after switch-off. Dirt can also stop a valve sealing or moving properly.
- Burned-out coilA burned-out coil will not open the valve. Check the wiring and voltage first; if the coil has failed, ask the maker for a replacement coil.
- Controller switching near its set pointA pH controller turns the solenoid on and off to hold the pH you set, so some clicking is part of how it works. Check the controller's manual for how it switches.
- Loose parts or wearA loose top nut or dirt or wear in the armature can cause humming. Tightening it or cleaning the armature tube may help.
Fix it now
- If CO₂ will not stop or fish are gasping, close the cylinder valve and follow the Too much CO₂ guide
- Unplug the solenoid, then check the plug, timer and socket, and that the power supply matches the solenoid's rated voltage
- Check the working pressure is above any minimum in your valve's specification, then plug it back in and allow time for pressure to settle before judging the lag
- If you use a pH controller, read its manual to see how it switches the socket before blaming the valve
- If gas flows when it should be off, unplug the solenoid, disconnect the regulator from the cylinder and vent the gas until both gauges read zero, then clean the orifice and plunger following the maker's procedure and leak-test with soapy water
- If it still fails, replace the coil or the solenoid, or ask the maker; do not keep a faulty valve in use
Stop it coming back
- Use a solenoid made for gas and match the power supply to its rated voltage
- Check the solenoid still closes properly whenever you change the cylinder
- Put the solenoid on a timer or controller so CO₂ stops at night
Common questions
- Is some lag after the CO2 solenoid opens normal?
- The maker advises not adjusting the flow straight after the solenoid is powered on, which suggests the system needs time to settle. A long delay can point to low working pressure, a power fault or dirt in the valve; check those in turn.
- Why does my solenoid keep clicking with a pH controller?
- A pH controller turns the solenoid on and off to hold the pH you set, so some clicking is part of how it works. If it seems excessive, read the controller's manual for how it switches before blaming the valve.
- Why does the solenoid hum or buzz loudly?
- A slight hum from an AC coil can be normal. A loud buzz can mean the wrong voltage or supply, so unplug it at once. A loose top nut or dirt in the armature can also cause humming.
Still stuck?
Describe the problem and share a photo in the WhatsApp community group. Other keepers can often spot what is wrong.
Sources
How we made this
Written with AI assistance from the sources listed here and checked against them (September 2026). Not yet reviewed by an expert. Report a mistake · How we write and check pages
Cite this page
Copy a ready-made line to credit this page in your own writing.
Citation
Scape Eden. “CO2 solenoid clicking or not working: fixes”. Scape Eden aquarium wiki, updated October 15, 2026. https://scapeeden.com/wiki/problems/co2-solenoid-not-working
Reference style (APA)
Scape Eden. (2026, October 15). CO2 solenoid clicking or not working: fixes. Scape Eden. https://scapeeden.com/wiki/problems/co2-solenoid-not-working
Plain link
https://scapeeden.com/wiki/problems/co2-solenoid-not-working
Text and data compiled by Scape Eden are free to reuse under CC BY 4.0 with attribution (credit Scape Eden and link to this page). Photos keep their own credited licences. Records are AI-assisted drafts with cited sources: see how we write and check this.
