Wiki
Layout and setup

Wavy glass or uneven silicone on a new tank

Also calledglass distortion new tankair bubble in siliconesilicone thickness uneventank bowed at bottomtank glass not flatbubbles in aquarium seam

New tanks often show ripples in reflections or a thicker silicone bead on one side. Glass bending a little under water is normal, but we found no maker or standard that says how much is acceptable, so ask the maker about any gap in a seam, a rocking tank or damage you can see.

How urgentFix this week

Not an emergency, but it gets worse if left.

What you see

  • Ripples or waves in the reflections when you look along the glass at an angle
  • A front pane that bows out slightly when the tank is full
  • Silicone that is thicker on one side or at one corner
  • Air bubbles inside a seam, or a gap in the silicone
  • A tank that rocks or has a gap under the base

Could it be something else?

  • A chip or crack in the glass: A chip is a missing flake, and a crack is a line through the glass. Neither is cosmetic: do not fill the tank until the maker or a glazier has seen it
  • A leak: A leak shows as damp, drips or water on the stand. Unplug equipment at the wall, then drain the tank by pump

Why it happens

  1. Normal bending under waterOne maker's manual says glass bends under water pressure, that this is natural, within the accepted standards, and does not affect safety.
  2. Heat-treated (toughened) glassIf the glass is toughened, it sags slightly between the rollers in the furnace and leaves ripples called roller wave. The glass trade says it cannot be removed completely, is normally seen only in reflections, and that thinner and larger panes show more.
  3. Uneven stand or floorThe same maker says the tank and cabinet must be level and that rocking from an uneven floor is not allowed. It also says to use a dedicated base or a mat that fits the tank.
  4. Silicone bead and bubblesThe maker manuals and standards we found do not give an acceptable bead width or bubble size. One maker guarantees the tightness of its junctions for 24 months, but its warranty does not cover visible damage to the silicone.
Step by step

Fix it now

  1. Empty the tank and keep it empty. Look at the glass and every seam in daylight, then take clear photos of any ripples, bubbles, gaps or thick and thin areas before you do anything else
  2. Check the stand: the tank and cabinet must be level on a flat, even surface, with the tank resting on a base or mat made to fit it. If the tank rocks, fix the stand before you fill
  3. Contact the seller or maker in writing before you fill if you see gaps in the silicone, damage to a seam or a very uneven bead. One maker's warranty excludes visible damage to the silicone, so show them the photos first
  4. If they say the tank is fine, fill it slowly in the place where it will stay, with no animals and the heater, filter and lights unplugged. Watch the seams as the water rises and again over the next days
  5. Never cut or trim silicone at a joint. If a seam does leak, drain the tank by pump and fix it with aquarium-safe silicone, letting it cure fully before you refill slowly
  6. A badly cracked pane may need replacing and silicone may not hold a big tank, so call a professional or the maker

Stop it coming back

  • Look over a new tank for defects as soon as it arrives, before you buy a stand, filter and scape
  • Place the tank on a stand made for aquariums, level, on a base or mat that fits it
  • Never lift a tank by its edge, and never lift or move it when it holds water

Common questions

Is it normal for the glass to look wavy on a new tank?
Ripples seen in reflections are a known effect of heat-treated glass, and the glass trade describes them as an optical effect. We found no maker or standard that gives an acceptable amount, so ask the maker if you are worried.
Are air bubbles in the silicone a problem?
We found no maker or standard that sets an acceptable bubble size. Photograph the bubbles and any gap before you fill, and ask the maker or seller if they look large or reach across the joint.
The silicone is thicker on one side. Is the tank safe?
We found no maker or standard that sets how even the silicone must be. Photograph it, check for gaps, and ask the maker if the joint looks thin or gappy.
Why does the front glass bow out when I fill the tank?
A small outward bend is normal because water pushes on the glass, and one maker says it is within the standards. If the bend worries you, or the tank rocks on its stand, empty it and ask the maker.
Scape Eden community

Still stuck?

Describe the problem and share a photo in the WhatsApp community group. Other keepers can often spot what is wrong.

Sources

  1. Aquael: aquarium manual (conditions of use and warranty)
  2. IQ Glass UK: Roller wave
  3. Loctite: how to patch a leaky fish tank with aquarium silicone
  4. Aqueon: frequently asked questions (stand and glass)

How we made this

Written with AI assistance from the sources listed here and checked against them (September 2026). Not yet reviewed by an expert. Report a mistake · How we write and check pages

Cite this page

Copy a ready-made line to credit this page in your own writing.

Citation

Scape Eden. “Wavy glass or uneven silicone on a new tank”. Scape Eden aquarium wiki, updated October 15, 2026. https://scapeeden.com/wiki/problems/wavy-glass-or-uneven-silicone

Reference style (APA)

Scape Eden. (2026, October 15). Wavy glass or uneven silicone on a new tank. Scape Eden. https://scapeeden.com/wiki/problems/wavy-glass-or-uneven-silicone

Plain link

https://scapeeden.com/wiki/problems/wavy-glass-or-uneven-silicone

Text and data compiled by Scape Eden are free to reuse under CC BY 4.0 with attribution (credit Scape Eden and link to this page). Photos keep their own credited licences. Records are AI-assisted drafts with cited sources: see how we write and check this.