
Eleocharis acicularis
- GroupFlowering plant
- OrderPoales
- GenusEleocharis
Dwarf hairgrass is an easy lawn plant that knits fine green blades together with creeping runners. Its blades are a little thicker than those of the finer Eleocharis parvula, so it suits the midground or a tank seen from a distance as well as the front. It roots well in sand with root tabs and stands up to Corydoras once it is established. It prefers cooler water and suffers in heat.
How it grows
- Split each pot into small plugs before planting.
- Trim to about 2 cm, which makes it send out more runners. Start once it reaches 4–5 cm.
- In sand, add root tabs.
- Trim off old tips, where hair algae and black beard algae settle.
- In a warm tank, trim every 2–3 weeks so the lower blades do not die from shade.
How to multiply it
Will it grow in my water?
Type your own readings, or compare typical tap water from a few cities. The yellow pin is your water; the striped band is where it survives, the solid band is its comfort zone.
Good fit for your water
All readings sit inside its range.
Type your own readings from a test kit. Guidance, not a guarantee.Where it can live
Underwater
Yes
Above water
Yes
Pond
Yesest.
Frost
Takes hard frostest.
Nano tank
Yesest.
Connections
Tap a linked problem for causes and a step-by-step fix.
Hairgrass in the wild
It grows wild across Europe, central and southeastern Asia, North America and northeastern South America as far as Ecuador. It is probably an introduction in Australia. In nature it lives in marshes, vernal pools and bogs and spreads from a creeping rhizome. In shallow water it makes short spikes of tiny flowers, under 5 mm across. It is also called needle spikerush, and the name acicularis means needle-shaped. It suits outdoor ponds too.
Hairgrass: planting and trimming
Push each small clump about 1 cm into the substrate and leave 1.5–2 cm between clumps, so the runners can link them up. For a dry start, use fine aquasoil 3–5 cm deep and plant from the back to the front. Out of water the leaves take CO₂ from the air, the roots anchor deeply and algae cannot grow. Keep humidity near 100% under cling film. Expect little growth for two weeks, runners at weeks 4–6 and a full carpet by weeks 6–8.
Hairgrass: why it melts or fades
Flood slowly: fill to 2–3 cm above the carpet, wait 24 hours, then fill the tank completely. Some leaf melt after flooding is normal. Aim for 50–80 PAR at the substrate and start CO₂ straight away, keeping it steady. Liquid carbon can help a low-tech tank through the switch.
Similar plants
Work it out
Sources
est. marks an estimate or a figure only one source gives.
How we made this
Written with AI assistance from the sources listed here and checked against them (September 2026). Not yet reviewed by an expert. Report a mistake · How we write and check pages
Cite this page
Copy a ready-made line to credit this page in your own writing.
Citation
Scape Eden. “Hairgrass care: light, CO2 and placement”. Scape Eden aquarium wiki, updated October 9, 2026. https://scapeeden.com/wiki/plants/eleocharis-acicularis
Reference style (APA)
Scape Eden. (2026, October 9). Hairgrass care: light, CO2 and placement. Scape Eden. https://scapeeden.com/wiki/plants/eleocharis-acicularis
Plain link
https://scapeeden.com/wiki/plants/eleocharis-acicularis
Text and data compiled by Scape Eden are free to reuse under CC BY 4.0 with attribution (credit Scape Eden and link to this page). Photos keep their own credited licences. Records are AI-assisted drafts with cited sources: see how we write and check this.
